fpit(4) - Linux man page

Name

fpit - Fujitsu Stylistic input driver

Synopsis

Section InputDevice  Identifier idevname  Driver fpit  Option Device
devpath  ...
EndSection

Description

fpit is an Xorg input driver for Fujitsu Stylistic Tablet PCs.

The fpit driver functions as a pointer input device, and may be used as the X server's core pointer.

Supported Hardware

This driver supports the touchscreen of the Stylistic LT and (with special options) of the Stylistic 500, 1000 and 2300.

Under Linux the Fujitsus serial port is not, by default, detected. Therefore the following must be added to one of your start-up scripts. (Either one of the X scripts, or to rc.local or similar).

setserial /dev/ttyS3 autoconfig
setserial /dev/ttyS3 IRQ 15 baud_base 115200 port 0xfce8

This driver now supports Stylistic 3400 (and possibly other passive-pen systems) with a special "Passive" paramter. Try this serial configuration for the 3400:

setserial /dev/ttyS3 autoconfig
setserial /dev/ttyS3 uart 16450 irq 5 port 0xfd68

Configuration Details

Please refer to xorg.conf(5x) for general configuration details and for options that can be used with all input drivers. This section only covers configuration details specific to this driver.

The device supports the following options:

Option "MaximumXPosition" "number"
Sets the maximum X position, use this to calibrate your touchscreen's right hand edge.
Option "MinimumXPosition" "number"
Sets the minimum X position, use this to calibrate your touchscreen's left hand edge.
Option "MaximumYPosition" "number"
Option "MinimumYPosition" "number"
Same as for X axis, but for Y axis.
Option "InvertX"
Option "InvertY"
Invert the specified axis.
Option "SwapXY"
Swap the X and Y axis.
Option "Rotate" "CW"
Option "Rotate" "CWW" Manipulate the invert and swap options to match screen rotations.
Option "DeviceName" "name"
Option "DeviceName" "name" sets the name of the X device.
Option "AlwaysCore" "on"
enables the sharing of the core pointer. When this feature is enabled, the device will take control of the core pointer (and thus will emit core events) and at the same time will be able, when asked so, to report extended events. You can use the last available integer feedback to control this feature. When the value of the feedback is zero, the feature is disabled. The feature is enabled for any other value.
Option "DebugLevel" number
sets the level of debugging info reported.
Option "BaudRate" "38400", "19200" or "9600" (default)
changes the serial link speed.
Option "Passive"
decodes the passive pen.

Example, for Stylistic LT setup is:

Section InputDevice  Identifier mouse0  Driver fpit  Option Device   /dev/ttyS3EndSection

And for other Stylistic devices try:

Section InputDevice  Identifier mouse0  Driver fpit  Option Device   /dev/ttyS3
 Option BaudRate 19200  Option MaximumXPosition 6250  Option MaximumYPosition
4950  Option MinimumXPosition 130  Option MinimumYPosition 0  Option InvertYEndSection

For Stylistic 3400:

Section InputDevice  Identifier mouse0  Driver fpit  Option Device   /dev/ttyS3
 Option BaudRate 9600  Option MaximumXPosition 4070  Option MaximumYPosition
4020  Option MinimumXPosition 0  Option MinimumYPosition 0  Option Passive
 Option SendCoreEventsEndSection

Authors

Original FPIT port: Rob Tsuk <rob@tsuk.com> and John Apfelbaum <johnapf@linuxslate.com>

X4 Port: Richard Miller-Smith <richard.miller-smith@philips.com>, based on Elographics code from: Patrick Lecoanet

X4.2 Cleanup: Alan Cox

Referenced By

xorg.conf(5)